Herringbone Headboard

headboard-final

I’m so excited to post about our most recent project, our herringbone headboard.  We were able to create this fun look for just about $40. We utilized various stains we had on hand, which saved on cash.  If you are planning to recreate this on a tight budget, ask around!  I’m sure you know someone with some extra stain in their garage looking for a project. Here’s a list of the tools and supplies we used.

  • Miter Saw
  • Finish Nailer and compressor
  • Hammer, Screws, Nails (to distress)
  • Various Stains
  • Chalk Line
  • Level
  • 1″x2″s (I used 3)
  • 1″x1″ (around 40)

Since I wasn’t looking for a “perfect” look, I used the cheapest wood I could find which cost less than a dollar a stick.

To begin, I laid all of the wood out on top of a drop cloth, pulled out my hammer, and started attacking.  That’s right, I wanted dents and dings galore!  I used screws on their sides, and indented the wood by hitting them with a hammer. I indented nail heads into the wood, and used the hammer itself (both sides) to make indentations.   After my wood took the beating, I stained each piece various colors using stains I had in the garage.

img_6761

 

Once my wood was ready to go, we got out the chalk line and marked the perimeter vertical lines for our edge pieces, and the center vertical line for a guide when nailing. We were sure to check our top and bottom horizontal lines with a level, and chalk those out too. One can’t assume walls and ceilings are straight or level especially in older homes. We then nailed all of the perimeter pieces.  We chose to make the sides about two inches wider on each side than our queen bed frame.  Now we were ready to set up the miter saw (for 45 degree cuts), compressor, and nail gun. It was time to start cutting! Seth cut while I nailed. It went fairly quickly once we got in a groove.  We started by cutting the edge of a 1″x1″ at a 45 degree angle. Then we put the board inside perimeters and  marked it at the center line. Now to cut and nail. 🙂 We could measure the length beneath, or we could use the board above to measure the board that would fill in beneath by using the length of the bottom to measure the length of the top of the next board we cut. We chose the latter).  We alternated sides as we went so that we were sure things fit properly. We used 1″x2″ boards randomly in a couple places throughout.

img_6795-2         img_6797-1

After the bottom was filled, it got easy for awhile. We continued using the same length as the first board cut until we got to the top where the boards get shorter again.  Then we just repeated the process again until it was completely filled in.
headboard-1

There you have it!  The whole process only took a few hours, and I’m really happy with how it turned out.

Now to finish painting! Ha!

Next I plan to make some side shelves with matching wood and copper piping.  I want something a little less industrial than the galvanized piping, and I think copper will look great!  So, stay tuned for that post!

I love owning a home because it allows me to let my creative juices flow without limit! If you live in the Colorado Springs area, and are interested in buying or building a home, call my husband! He loves serving families and individuals in our community by helping them find their perfect nest.  Check him out on Facebook here. Thanks for reading!

Lathe Accent Wall

I wanted to add some serious “hello” type character to our tiny dining room, and found a picture(here) that inspired me.  I LOVE the look of well-done pallet walls and pallet furniture, but let’s be honest, it’s getting to be a liiiittle overdone, right? Then I saw the lathe!  If you aren’t familiar, lathe is small wood strips that are used behind plaster walls. I a firm believer in reclaiming, reusing and recycling, but I had a really hard time finding any old lathe locally.  So, off to Home Depot I went. Lathe comes in bundles for around $12. I think I used three for this wall.

IMG_4176

IMG_4254

So here’s a brief run down of the process. If you want more deets or have questions, feel free to message me below. 🙂 Because I wanted a rustic-meets-industrial look in this area, after a brief sand, I took a hammer and a couple nails to destruct the wood a little.  I hammered the sides of screws. nailed and removed nails, impressed nail-heads, and just smacked it with a hammer to get a bit more of a used look.  Then I used various stains to treat the wood.  I’m not 100% cracked on the colors I used, but it works.  After this, per my husband’s advice, we made horizontal chalk lines at various places throughout the wall. This kept me on track as I worked my way up, so that I didn’t end up crooked (good call, hubs!). We also chalked some vertical lines where studs were, so that I nailed the piece of lathe into at least one stud. I didn’t want my work falling off!  I used a nail gun to nail each piece of lathe on to the wall, and a miter saw to cut the end pieces. It went fairly quickly. I had to be sure to stagger my different colors of lathe since I used various stains, but other than that it was just nail, nail, nail, cut. I’m pretty happy with the result!

I finished the room with a great over-sized, industrial pendant light from Ikea, and some taboret chairs from Overstock. Most of my frames and mirrors were thrift store finds.

IMG_4259IMG_4256

IMG_4178IMG_2047

And of course, I have to include the “before” picture. It’s quite strange, really.  Stone wall, no fireplace. Carpeted closet in the dining room?  I love that I can change whatever I want, and be as creative as I want!  If you are interested in home ownership and live in the Colorado Springs area, go here or go to Seth’s Facebook page!

Hope this has inspired you to let loose and be creative as you design your home!

Name(required)
Email(required)
Website
Comment(required)